Showing results: 31 - 45 of 171 items found.
-
Y1203A -
Keysight Technologies
Use to interconnect PXIe and AXIe chassis in a multi-chassis system or to connect a PC host card to a PXIe system module.
-
4821 -
Technobox, Inc.
The XMC2PCE is a passive 8X XMC to PCI express carrier card which permits the use of XMC cards in PC style PCI express 1X, 2X, 4X, 8X or 16X motherboard slots.
-
PCCextend 140 -
Sycard Technology
The PCCextend 140 was designed from the ground up to support the higher data rates and controlled impedance requirements of the CardBus interface. Fabricated on a six-layer board, the PCCextend 140 is designed to minimize signal degradation in the 33MHz CardBus environment. The PCCextend 140 is compatible with all release 2.1 and both 16-bit PC Card and CardBus-capable PC Card 95 sockets.
-
GPIB-PCI-E -
Ines GmbH
The GPIB-PCI-E is a PCI Express GPIB controller card that converts any PC with a PCI Express slot into a GPIB controller.
-
PCIe, PCI, PC/104, CAN -
BMC Messsysteme GmbH
PC data acquisition cards are particularly suitable for stationary measurement applications. Outstanding in this category are the PCI(e) multi-function cards PCI-BASEII and PCIe-BASE on which you can plug different measurement and control modules to optimize the price-performance ratio.
-
LE-270A -
LINEEYE Co., Ltd.
LE-270A is a Communication Data Logger, which records CAN/LIN communication logs in the SD/SDHC card for long hours. Using with a PC, it performs as a CAN/LIN protocol analyzer, and monitors data on the PC at real time (Line Monitor). Using without a PC, it performs as the CAN/LIN data logger, and saves data in the SD/SDHC card. It has two High-speed CAN transceivers, two Low-speed CAN transceivers and two LIN (TJA1020) transceivers. It monitors two channels of CAN or LIN, or one CAN and one LIN transceivers. In addition, four channels of Analog/Digital signals can be recorded.
-
Plottergeist -
Aphena Ltd
Plottergeist "the phantom plotter" emulates all the common HPGL plotters. It runs on a standard PC equipped with a GPIB card or using RS-232, and connects to test equipment or another computer. The software behaves like a real plotter, with the exception that the PC screen is the paper.
-
Sealevel Systems, Inc.
Sealevel PCI Express digital I/O cards are designed for computers with X1 PC Express slots and are compatible with any PCI Express slot. Digital I/O cards are currently available with optically isolated inputs and Reed relay outputs. Optically isolated inputs protect the PC from voltage spikes common to industrial environments while Reed relay outputs provide reliable, long-life switch closures suitable for low current applications.
-
PCI EmbeddedComputer Systems
This adapter can be used to run, test or program a 3U VPX card in a standard PC PCIe slot. SSC switchable (ON/OFF) PCs available from PCI-Systems Inc.
-
90386 -
HITEC Sensor Solutions Inc.
The 90386 is a portable sensor interface that powers and processes strain gaged based sensor into USB compatible signals. No need for additional signal processing or special PC cards.
-
APC8621A -
Acromag, Inc.
This board interfaces industry-standard Industrial I/O Pack (IP) modules to a PCI bus on a PC-based computer system. The half-length card is ideal for use in smaller PC chassis.
-
CF extend 180 -
Sycard Technology
The CF extend 180 is a flexible extender card designed to provide easy access to a CompactFlash™ card for debug or test. Designed with the same low noise characteristics of our CF extend 160, the CF Extend 180 takes this design a step further by connecting the host and card via ribbon cables. The flexible extender consists of two PC boards, the host interface board and the card interface board.
-
COND25-1553 -
Abaco Systems Inc
Commercial Application Transitions from a 25 pin D-sub connector on a PC expansion card end-panel to two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends. Military Application Transitions from a 25 pin D-sub connector on a PC expansion card end-panel to two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and two 18" cables with BNC cable jacks for I/O triggers.
-
PCCextend 125CIB -
Sycard Technology
For those applications that require access to the CardBus PC Card that can't use a standard extender card, Sycard provides the PCCextend 125CIB (Card Interface Board) which allows full access to all 68-signal and power pins on the CardBus peripheral. Standard 0.1" headers allow the user to connect standard 34-pin ribbon cable to test or prototype hardware.
-
41-924-001-KIT -
Pickering Interfaces Ltd.
The kit is supplied with a PCIe card which can plug into any PC PCIe slot, a PXI module for insertion into Slot 1 of a PXI chassis and 3m lead to connect the two parts together. The interface uses a single lane PCIe connection from the PC to provide a software transparent link from the PC PCIe backplane to the PXI backplane. The supplied 3m shielded lead ensures the system has robust operation and an adequate separation distance between the PC and the PXI chassis.